FRP / Rider review

FRP GMB100 Review: LNSPLTBLVD Builds a 99cc Mini Bike and Climbs a Hill

LNSPLTBLVD unboxes and assembles a black FRP GMB100, examines its controls and rides up a dirt hill. The speed reading is not a verified maximum.

Black FRP GMB100 99cc gas mini bike photographed from LNSPLTBLVD original rider video
My black GMB100 after I put the front end together. Still frame from the video.

I started with a GMB100 in a carton, the front wheel and front-end pieces still to put on. I filmed the assembly, took the black bike outside for a closer look, then tried a dirt hill. This FRP GMB100 review follows those moments rather than treating my ride as a controlled performance test.

The short version

  • I assembled the front end of the 99cc mini bike and said the build was straightforward.
  • I liked the covered chain, rear carrying handle and engine stop switch at the handlebar.
  • I rode up a dirt hill and made it to the top.
  • I reported a 24 mph reading, but did not show the measuring method; FRP currently lists 28 mph.

My review: I found the GMB100 straightforward to assemble, liked the covered chain and rear handle, and made it to the top of the dirt hill in my video.

Watch my GMB100 unboxing and front-end assembly

A 35-second muted excerpt of the original workshop build. See the FRP GMB100

What came with my black 99cc mini bike?

I lifted out the GMB100 and set the parts next to it. I showed a rechargeable LED light, a bag of tools, handlebar clamps, the steering pivot and the front axle. My footage shows what was in my box, not a promise that every package contains the same extras: FRP's current product page lists the light with its Starter Kit and Complete Bundle.

LNSPLTBLVD assembling the FRP GMB100 99cc mini bike front end
The separate front-end parts beside my GMB100.

Putting the GMB100 together

I worked on the front wheel, fork and fender while the rest of the bike sat on the garage floor. By the time I rolled it outside, the front end was in place. I added oil before the first start; for the correct amount and checks, follow the included FRP manual instead of treating my footage as instructions.

I later described assembly as straightforward. That is my experience with this bike; FRP lists the current GMB100 as 85% pre-assembled.

The details I kept noticing

Outside, I showed the rear disc brake, the cover over the chain, the engine stop switch beside the throttle and the handle behind the seat. I liked the full-cover chain guard. Having the switch right at the handlebar stood out to me, and I used the rear handle to show how I could move the bike around.

FRP GMB100 99cc mini bike handlebar controls shown in LNSPLTBLVD video
The controls I pointed out during my first look.

How did this gas mini bike do on a dirt hill?

I took the bike up a dry dirt hill and reached the top. That is the hill-climb result I can stand behind from my video; I did not measure the slope or run a repeatable test. I also said I clocked 24 mph earlier, but the footage does not show how I measured it, so I would not present it as a verified top speed. FRP currently lists 28 mph as its GMB100 figure, not a result from my ride.

The embedded clip here stays with the workshop assembly. For a GMB100 gas mini bike, follow the manufacturer's off-road guidance and ride only in permitted areas with protective gear.

FRP GMB100 specs and packages

Spec GMB100
Engine 99cc-class four-stroke OHV
Start and brake Pull start; rear disc brake
Maximum rider load 220 lb
Net weight 79.5 lb
Fuel tank 1.38 L
Assembly 85% pre-assembled; follow the manual
Listed top speed 28 mph (FRP figure; not my measurement)
Current price $399.99–$449.99 across current variants

These are the current FRP product-page specifications and prices, not test measurements from my video.

GMB100 build and riding questions

What is shown in this FRP GMB100 review?

I unboxed and assembled the black GMB100, showed its controls outside, and rode up a dirt hill. My short embedded excerpt only shows the build; it does not show the later ride.

What came in the GMB100 box I opened?

I showed a rechargeable LED light, a tool bag, handlebar clamps, the steering pivot and the front axle. FRP currently lists the light with the Starter Kit and Complete Bundle; package contents depend on the option selected.

How did assembling the 99cc mini bike go?

I put the front end together and later said assembly was straightforward. FRP lists the GMB100 as 85% pre-assembled; the included manual is the guide for assembly and pre-ride checks.

What did I notice on the completed bike?

I pointed out the rear disc brake, the full-cover chain guard, the engine stop switch beside the throttle and the handle behind the seat. I liked having the switch at the handlebar and the handle for moving the bike.

Did I measure GMB100 top speed?

I said I had clocked 24 mph earlier, but the video does not document the measuring method. That is one rider's reported reading, not a verified maximum. FRP currently lists 28 mph as its product figure.

Did the GMB100 climb the hill?

I rode up the dirt hill in the video and said the bike made it to the top. I did not measure the grade or conduct a repeatable hill-climb test.

What are the GMB100 engine and rider-load specs?

FRP lists a 99cc-class four-stroke OHV engine, pull start, rear disc brake and 220 lb maximum rider load. These are product-page specifications, not my measurements.

How does this mini bike ship and what warranty applies?

The FRP product page lists FedEx Home Delivery and a one-year limited warranty. Check the current checkout and warranty terms before ordering.

Can the GMB100 be ordered in California?

FRP's product page says this model is not available in California. The GMB100 is intended for permitted off-road use with appropriate protective gear.

Explore the GMB100

The GMB100 product page lists current colors, packages and assembly information.

Shop the GMB100

Written from videos posted by LNSPLTBLVD and edited by FRP Moto.